For Technical Assistance
1-800-845-8345
Electric Shock Hazard: Using an ungrounded or improperly connected
appliance can result in serious injury or death from electrical shock.
Turn off water supply.
If using the sink sprayer hose hole,
remove nut that connects sprayer
hose at bottom of faucet.
Using adjustable wrench, remove nut
connecting sprayer washer flange in
sprayer hole.
Plug hose opening with either a 1/8"
plug or a 1/4" cap (not supplied).
b
If you have to drill through
sink or countertop, you may need to
rent or purchase the appropriate tools.
PREPARATION
START HERE
PROPER INSTALLATION SHOULD TAKE ABOUT 2-4 HOURS
Identify locations for the dispenser
faucet, tank and filter (if applicable).
Check to make sure there is proper
clearance (see chart at left) for
dispenser handle to be fully opened.
Check to make sure counter is 3"
thick or less.
Make sure there is a grounded
electrical outlet within 30" of the tank.
1
A
The wall outlet for your dispenser must have
power supplied to it continuously and must be
fused. It should not be controlled by the same
wall switch that operates your disposer.
Note: Hole size requirement is 1
1
⁄
4
"
– 1
1
⁄
2
"
Required minimum from
center of hole to wall is 4
3
⁄8
1
2
3
Brass Nut
Ferrule
Brass Insert
Brass Nut
1/4"
copper tube
Ferrule
1
2
3
Brass Nut
Ferrule
Brass Insert
Brass Nut
1/4"
copper tube
Ferrule
This appliance must be grounded. This instant hot water dispenser is equipped with a cord that has
a grounding conductor and a grounding pin. The plug must be connected to an appropriate outlet that is
properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided with the appliance.
1
2
3
Brass Nut
Ferrule
Brass Insert
Brass Nut
1/4"
copper tube
Ferrule
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
C1300
C1300
C1300
C1300
From under the sink, place the
semi-circular mounting plate onto the
threaded stud.
Place hex nut onto the threaded stud.
Ensure faucet is at desired angle.
Insert screwdriver into hole on side of
hex tool (creating a “T”), and use tool
to tighten nut and secure faucet.
2
Semi-circular mounting plate should
encircle all descending tubes and
extend beyond sink hole when tight.
Ensure that the black O-ring is
properly seated in the base of the
faucet (the groove on the underside
of the faucet base).
1
2
3
Brass Nut
Ferrule
Brass Insert
Brass Nut
1/4"
copper tube
Ferrule
1
2
3
Brass Nut
Ferrule
Brass Insert
Brass Nut
1/4"
copper tube
Ferrule
1
2
3
Brass Nut
Ferrule
Brass Insert
Brass Nut
1/4"
copper tube
Ferrule
Feed tubes down through the hole
in the sink or countertop until the
base is at rest on the sink or
countertop surface.
1
2
3
Brass Nut
Ferrule
Brass Insert
Brass Nut
1/4"
copper tube
Ferrule
Unpack dispenser components.
On a firm, flat surface, carefully
straighten the copper tubing.
An assistant may be needed
to hold the faucet in place
while securing the dispenser.
b
A
c
d
Make sure to use rubber O-ring
to ensure proper seal.
INSTALLING THE FAUCET - C1300
NOTICE
5
4
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals