InSinkErator F-1000S Instruction Manual download pdf (Page 3)

F-1000 Cartridge (included with this system) Chemical & Mechanical Reduction Filter Specifications:

This cartridge provides mechanical and chemical reduction of chlorine taste & odor and particulate class III.

Filter Capacity:

500 gallons, depending on local water conditions. Note that while the testing was performed under

standa

rd laboratory conditions, actual performance may vary. Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection befo

re or after the system. For cold water use only.

Systems must be

installed and operated in accor

dance with the Manufacturer’s recommended procedures and guidelines. See warranty

rd for warranty. For service and parts, contact your local dealer or InSinkErator

directly at 1-800-558-5700.

pplication guidelines/Water Supply Parameters for NSF Testing: Service flow of 0.75 gpm, community or

private well water suppl

y, water pressure of 20-120 psi (138-827 kPa), water temperature of 33˚F–100˚

Nominal

Particulate Class III,

≥5 µm to <15 µm

270,000 pts/mL

2.1 mg/L 2.0 mg/L ± 10%

At least 10,000

particles/mL

82 pts/mL 99.9%

≥85%

0.06 mg/L 97.0%

≥ 50% J-00082587

J-00119308

F Except as

noted, all testing performed at pH = 7.5

± 0.5, Flow: 0.75 gpm, Pressure: 60 psi, Temp: 20˚± 3˚C.

Contact an authorized InSinkErator service agent for repairs or replacement components. Replacement filters

F-1000 and F-2000 can be ordered by calling 800-558-5700, visiting shop.insinkerator.com, or by contacting

an authorized InSinkErator reseller.

Refer to the Performance Data Sheet for InSinkErator Filter System Model F-2000S

Replacement Cartridge: F-2000

Pressure: 30-120 (207-827 kPa) psi

Temperature: 33

F - 100

Flow Rate: 0.75 gpm

Capacity: 500 gallons

Tested & Certified by NSF International against NSF/ANSI Standard 42 in the following

InSinkErator Systems Only: GN1100, HC1100, GN2200, HC2200, GN2215, HC2215,

H3300 or HC3300 for the reduction of claims specified on the Performance Data Sheet.

For systems using two handle HC model faucets, operate only one handle at a time.

Turn off water supply before starting.

Installation must comply with all state and local laws and regulations.

Property Damage: Do not extend the lines farther

than the 16" provided. Ensure tube(s) and “Y”

connnector are securely fit.

Personal Injury: Do not locate filter above an

outlet or other electrical device. Install head and

bracket so that connections require no stretching,

kinking or pinching of tubing.

It is normal for approximately 2 oz. of water

to discharge when filter is removed.

Property Damage: Tube runs need to form to the

cabinet’s contours to allow storage space with no

sharp bends. Tubes need clean, perpendicular,

burr-free cuts to ensure a true fit.

From water

supply line

To dispenser

INSTALLING FILTRATION SYSTEM

From water

supply line

To dispenser

Scalding Hazard: The faucet dispenses near-boiling

(212ºF) water which can instantly cause scalds or

burns. Use care when operating this appliance.

Property Damage: Join remaining tube

to cold water supply only.

Turn on the water supply.

Depress the dispenser’s HOT handle

and hold it until water flows from the

spout (approximately 1 to 2 minutes).

For the F-1000S and F-1000, flush

2.25 gallons through filter before use

(approximately 3 minutes). For the

F-2000S and F-2000, flush 3 gallons

through filter before use (approximately

4 minutes).

Check all connections to ensure they

are tight and that there are no leaks.

Install a T-fitting (not included)

onto the cold water supply line.

Install dedicated water control valve

with 1/4" compression fitting.

At the end of the white 1/4" tube

from the filter or quick-connector,

slide the supplied brass nut and

ferrule over the tube and then push

in the brass tube insert.

Insert the white 1/4" tube into the 1/4"

compression fitting and tighten.

FINAL WATER CONNECTION

TURN ON WATER & CONNECT POWER

Brass Nut

Ferrule

Brass

Insert

1/4"

Plastic

Tube

From filter or

water supply line

Plug

From filter or

water supply line

HC1100, HC2200,

HC2215

GN1100, GN2200, GN2215,

HC3300, H3300

Determine length of tubing required,

then cut to length making sure the cut

is perpendicular and burr-free.

Insert a white 1/4" tube into inlet side

of filter head until it stops. Press in

again to ensure a secure fit.

Insert the other white 1/4" tube into

outlet side of filter head until it stops.

Press in again to ensure a secure fit.

Separate cartridge from filter head.

Mark hole locations for filter head

and bracket in a spot that allows

for filter replacement.

Drill 1/8" starter holes and attach bracket

to wall with wood screws, turning until snug.

Insert cartridge into filter head. Top

surface of cartridge will become flush with

bottom of filter head when fully engaged.

Connect remaining white 1/4" tube to

incoming water supply line.

Insert the copper tubes(s) from the

dispenser into “Y” quick-connector

using the plug for hot-only models.

Connect the white 1/4" tube from

the right outlet on the filter head into

the quick-connect fitting until it stops.

Press in again to ensure a secure fit.

To remove tube(s) or plug from quick-connector,

depress the release ring and gently pull away.

Screws provided are for use in wood

studs or cabinets only. Use wall anchors

(not supplied) for installation into drywall.

NOTICE

1 2 3 4 5 6 7 8 ... 11 12

Comments to this Manuals

No comments

InSinkErator F-1000S Instruction Manual Page 3

Comments to this Manuals